Линукс на плате CI20

[vak]

Протокол загрузки Linux Debian на плате MIPS Creator CI20.

[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.0.8-00094-gb4f0297c4d84 (asmith@asmith-linux) (gcc version 4.7.3 (Sourcery CodeBench Lite 2013.05-66) ) #1 SMP PREEMPT Wed Jun 25 12:25:25 BST 2014
[ 0.000000] CPU0: reset EPC:8F9D60AB
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 3ee1024f (Ingenic Xburst)
[ 0.000000] FPU revision is: 00330000
[ 0.000000] setup_priority: BUS--0x13000000, TARGET--0x6, VALUE--0x3
[ 0.000000] setup_priority: VALUE after setup--0xc0
[ 0.000000] setup_priority: BUS--0x13400000, TARGET--0xa, VALUE--0x3
[ 0.000000] setup_priority: VALUE after setup--0xc00
[ 0.000000] CCLK:1200MHz L2CLK:600Mhz H0CLK:400MHz H2CLK:200Mhz PCLK:100Mhz
[ 0.000000] Determined physical RAM map:
[ 0.000000] User-defined physical RAM map:
[ 0.000000] memory: 10000000 @ 00000000 (usable)
[ 0.000000] memory: 30000000 @ 30000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00020000
[ 0.000000] HighMem 0x00020000 -> 0x00060000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00010000
[ 0.000000] 0: 0x00030000 -> 0x00060000
[ 0.000000] On node 0 totalpages: 262144
[ 0.000000] free_area_init_node: node 0, pgdat 80791be0, node_mem_map 81000000
[ 0.000000] Normal zone: 1024 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 64512 pages, LIFO batch:15
[ 0.000000] HighMem zone: 2048 pages used for memmap
[ 0.000000] HighMem zone: 194560 pages, LIFO batch:31
[ 0.000000] [SMP] Slave CPU(s) 1 available.
[ 0.000000] PERCPU: Embedded 7 pages/cpu @81c07000 s5408 r8192 d15072 u32768
[ 0.000000] pcpu-alloc: s5408 r8192 d15072 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 259072
[ 0.000000] Kernel command line: console=ttyS0,115200 console=tty0 mem=256M@0x0 mem=768M@0x30000000 ubi.mtd=1 root=ubi0:root rootfstype=ubifs rw
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Primary instruction cache 32kB, VIPT, 8-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 8-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] allocated 6291456 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Memory: 1021440k/262144k available (6078k kernel code, 27136k reserved, 1620k data, 232k init, 786432k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:376
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled, bootconsole disabled
[ 0.009905] Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
[ 0.090047] pid_max: default: 32768 minimum: 301
[ 0.090298] Mount-cache hash table entries: 512
[ 0.090938] Initializing cgroup subsys cpuacct
[ 0.090990] Initializing cgroup subsys memory
[ 0.091036] Initializing cgroup subsys devices
[ 0.091055] Initializing cgroup subsys freezer
[ 0.091073] Initializing cgroup subsys blkio
[ 0.211585] CPU1: reset EPC:EFFFCA4A
[ 0.211600] CPU revision is: 3ee1024f (Ingenic Xburst)
[ 0.211607] FPU revision is: 00330100
[ 0.211622] Primary instruction cache 32kB, VIPT, 8-way, linesize 32 bytes.
[ 0.211632] Primary data cache 32kB, 8-way, VIPT, no aliases, linesize 32 bytes
[ 0.250105] Brought up 2 CPUs
[ 0.250151] [SMP] slave cpu1 start up finished.
[ 0.251044] devtmpfs: initialized
[ 0.253345] print_constraints: dummy:
[ 0.253578] NET: Registered protocol family 16
[ 0.253632] gpemc: SoC-jz4780 gpemc support functions initilized.
[ 0.254006] jz4780-bch jz4780-bch.0: SoC-jz4780 HW ECC-BCH support functions initialized.
[ 0.256606] GPIO sleep states:
[ 0.256626] OH:00000000 OL:00000000 IP:8700ff00 IN:080000ff
[ 0.256675] OH:00000000 OL:0e8fffc0 IP:f1300000 IN:00400030
[ 0.256718] OH:00000000 OL:0fffffff IP:f0000000 IN:00000000
[ 0.256761] OH:00002000 OL:00000209 IP:3c015000 IN:c3fe8d00
[ 0.256803] OH:00000000 OL:00000041 IP:0f0ffb20 IN:c0f00096
[ 0.256846] OH:00000000 OL:00e40680 IP:fc00d97f IN:03130000
[ 0.257087] jz_platform_init--->dmmu
[ 0.261649] bio: create slab at 0
[ 0.264560] jz-dma jz-dma: JZ SoC DMA initialized
[ 0.265099] SCSI subsystem initialized
[ 0.265267] usbcore: registered new interface driver usbfs
[ 0.265367] usbcore: registered new interface driver hub
[ 0.265716] usbcore: registered new device driver usb
[ 0.266092] i2c-gpio i2c-gpio.0: using pins 126 (SDA) and 127 (SCL)
[ 0.266220] i2c-gpio i2c-gpio.2: using pins 176 (SDA) and 177 (SCL)
[ 0.266348] i2c-gpio i2c-gpio.4: using pins 140 (SDA) and 141 (SCL)
[ 0.266438] jz-i2c jz-i2c.1: probe i2c1------>i2c1 i2c->speed 100
[ 0.266589] jz-i2c jz-i2c.3: probe i2c3------>i2c3 i2c->speed 100
[ 0.266909] Advanced Linux Sound Architecture Driver Version 1.0.24.
[ 0.267357] Bluetooth: Core ver 2.16
[ 0.267444] NET: Registered protocol family 31
[ 0.267484] Bluetooth: HCI device and connection manager initialized
[ 0.267532] Bluetooth: HCI socket layer initialized
[ 0.267573] Bluetooth: L2CAP socket layer initialized
[ 0.267632] Bluetooth: SCO socket layer initialized
[ 0.267895] cfg80211: Calling CRDA to update world regulatory domain
[ 0.269557] print_constraints: Vcc-5V: 5000 mV
[ 0.269655] reg-fixed-voltage reg-fixed-voltage.0: Vcc-5V supplying 5000000uV
[ 0.269809] print_constraints: ethnet: 3300 mV
[ 0.269900] reg-fixed-voltage reg-fixed-voltage.1: ethnet supplying 3300000uV
[ 0.270075] act8600 0-005a: register regulator:OUT1
[ 0.272493] print_constraints: Core: 1000 <--> 1400 mV at 1200 mV
[ 0.273217] act8600 0-005a: register regulator:OUT3
[ 0.275476] print_constraints: Vcc-IO: 3300 mV
[ 0.276167] act8600 0-005a: register regulator:OUT4
[ 0.276248] print_constraints: OTG-Vbus: 5000 mV
[ 0.276936] act8600 0-005a: register regulator:OUT6
[ 0.277006] print_constraints: Wi-Fi: 3300 mV
[ 0.277697] act8600 0-005a: register regulator:OUT7
[ 0.278231] print_constraints: Camera2.8: 2800 mV
[ 0.278924] act8600 0-005a: register regulator:OUT8
[ 0.279466] print_constraints: Camera1.8: 1500 mV
[ 0.280183] act8600 0-005a: register regulator:VBUS
[ 0.280254] print_constraints: Vbus:
[ 0.282746] print_constraints: USB Charger: 400 <--> 800 mA at 400 mA
[ 0.283595] Switching to clocksource jz_clocksource
[ 0.290040] Switched to NOHz mode on CPU #0
[ 0.290740] DWC IN OTG MODE
[ 0.290775] init PHY
[ 0.292001] Switched to NOHz mode on CPU #1
[ 0.333889] dwc2 dwc2: Keep PHY ON
[ 0.333940] dwc2 dwc2: Using Buffer DMA mode
[ 0.533704] dwc2 dwc2: Core Release: 3.00a
[ 0.533765] dwc2 dwc2: Total FIFO SZ=3576
[ 0.533773] dwc2 dwc2: Rx FIFO SZ=3648
[ 0.533781] dwc2 dwc2: NP Tx FIFO SZ=3648
[ 0.533802] dwc2 dwc2: Architecture: External DMA
[ 0.533817] dwc2 dwc2: DesignWare USB2.0 High-Speed Host Controller
[ 0.533895] dwc2 dwc2: new USB bus registered, assigned bus number 1
[ 0.534709] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.534763] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.534834] usb usb1: Product: DesignWare USB2.0 High-Speed Host Controller
[ 0.534880] usb usb1: Manufacturer: Linux 3.0.8-00094-gb4f0297c4d84 dwc2-hcd
[ 0.534926] usb usb1: SerialNumber: dwc2
[ 0.535418] hub 1-0:1.0: USB hub found
[ 0.535475] hub 1-0:1.0: 1 port detected
[ 0.535530] dwc2 dwc2: set feature 8
[ 0.535730] dwc2 dwc2: DWC2 Host Initialized
[ 0.536028] USB disconnect
[ 0.536073] dwc2 dwc2: enter dwc2_gadget_plug_change:2410: plugin = 0 pullup = 0 suspend = 0 ext_vbus = 0
[ 0.536255] NET: Registered protocol family 2
[ 0.536416] IP route cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.536810] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.537718] TCP bind hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.538593] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.538645] TCP reno registered
[ 0.538690] UDP hash table entries: 128 (order: 0, 4096 bytes)
[ 0.538757] UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
[ 0.539219] NET: Registered protocol family 1
[ 0.540652] Total 33MB memory at 0xe000000 was reserved for IPU
[ 0.541320] Total 16MB memory1 at 0xd000000 was reserved for IPU
[ 0.553775] highmem bounce pool size: 64 pages
[ 0.554052] ashmem: initialized
[ 0.560712] JFFS2 version 2.2. (NAND) \xffffffc2\xffffffa9\xffffffa9 2001-2006 Red Hat, Inc.
[ 0.561220] fuse init (API version 7.16)
[ 0.561681] yaffs: yaffs built Jun 25 2014 12:21:16 Installing.
[ 0.561717] msgmni has been set to 459
[ 0.566009] io scheduler noop registered
[ 0.566069] io scheduler deadline registered
[ 0.566221] io scheduler cfq registered (default)
[ 0.616940] jz-fb jz-fb.0: Frame buffer size: 24887296 bytes
[ 0.617502] graphics fb0: open count : 1
[ 0.633809] dwc2 dwc2: ID PIN CHANGED!
[ 0.644039] dwc2 dwc2: Total FIFO SZ=3576
[ 0.644047] dwc2 dwc2: Rx FIFO SZ=3648
[ 0.644054] dwc2 dwc2: NP Tx FIFO SZ=3648
[ 0.644061] dwc2 dwc2: Architecture: External DMA
[ 0.666685] ===> warning, wait lcd sof failed, please check, if enable sof in xboot
[ 0.666710] jz-fb jz-fb.0: LCDC: PixClock:148500000
[ 0.666718] jz-fb jz-fb.0: LCDC: PixClock:148000000(real)
[ 0.709377] Console: switching to colour frame buffer device 240x67
[ 0.855940] dwc2 dwc2: ++OTG Interrupt: Debounce Done++
[ 0.913790] dwc2 dwc2: set feature 4
[ 0.914951] ===> warning, wait lcd sof failed, please check, if enable sof in xboot
[ 0.915257] jz-fb jz-fb.0: LCDC: PixClock = 148500000
[ 0.915442] jz-fb jz-fb.0: LCDC: PixClock = 148000000(real)
[ 0.915719] (NULL device *): jzfb_check_var get video mode failed
[ 0.915946] jz-fb jz-fb.1: Not allocate frame buffer
[ 0.916969] jz-aosd jz-aosd: Frame buffer support AOSD
[ 0.917571] api_Initialize: dwc_hdmi_tx_software_api_2.12
[ 0.917785] api_Initialize: Jun 25 2014
[ 0.917945] api_Initialize: Product Line, 0xa0
[ 0.918107] api_Initialize: Product Type, 0xc1
[ 0.918271] api_Initialize: HDMI TX Controller Design, 0x13
[ 0.918470] api_Initialize: HDMI TX Controller Revision, 0x1a
[ 0.918676] api_Initialize: HDMI TX controller supports HDCP
[ 0.918885] ==================>enter hdcp_Initialize:25
[ 0.919255] hdmi phy disable,enable hpd
[ 0.919408] ====phy conf0=16 reset=1
[ 0.919830] =====>enable TX_INT in api_Initialize:187
[ 0.920076] api_EventHandler: hot plug detected
[ 0.920263] jz-hdmi jz-hdmi: HPD CONNECT
[ 0.920693] jz-hdmi jz-hdmi: Force HDMI init VIC 16
[ 0.920871] hdmi-phy-enable
[ 0.920983] phy_Initialize: GEN 2 TSMC 40LP 2.5V build - TQL
[ 1.303820] usb 1-1: new high speed USB device number 2 using dwc2
[ 1.304369] dwc2 dwc2: set feature 4
[ 1.722779] usb 1-1: New USB device found, idVendor=05ac, idProduct=1006
[ 1.723039] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1.723291] usb 1-1: Product: Keyboard Hub
[ 1.723441] usb 1-1: Manufacturer: Apple, Inc.
[ 1.723602] usb 1-1: SerialNumber: 000000000000
[ 1.724435] hub 1-1:1.0: USB hub found
[ 1.724748] hub 1-1:1.0: 3 ports detected
[ 1.763756] usb 1-1: USB disconnect, device number 2
[ 1.923791] Waiting for hot plug detection...
[ 1.923979] ====phy conf0=ce reset=0
[ 1.932832] edid_Initialize: reading EDID
[ 1.995303] edid_EventHandler: block checksum correct
[ 2.025094] dwc2 dwc2: ++OTG Interrupt: Debounce Done++
[ 2.057869] edid_EventHandler: block checksum correct
[ 2.066870] jz-hdmi jz-hdmi: EDID reading done
[ 2.067056] jz-hdmi jz-hdmi: ==========>HDMI mode
[ 2.084363] dwc2 dwc2: set feature 4
[ 2.084714] No HDCP parameters provided: not configured
[ 2.473777] usb 1-1: new high speed USB device number 3 using dwc2
[ 2.482564] dwc2 dwc2: set feature 4
[ 2.892643] usb 1-1: New USB device found, idVendor=05ac, idProduct=1006
[ 2.901304] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.909895] usb 1-1: Product: Keyboard Hub
[ 2.918484] usb 1-1: Manufacturer: Apple, Inc.
[ 2.926944] usb 1-1: SerialNumber: 000000000000
[ 2.935924] hub 1-1:1.0: USB hub found
[ 2.944435] hub 1-1:1.0: 3 ports detected
[ 2.993756] usb 1-1: USB disconnect, device number 3
[ 3.093766] jz-hdmi jz-hdmi: ----api_Configure ok
[ 3.106286] jz-uart.0: ttyS0 at MMIO 0x10030000 (irq = 59) is a uart0
[ 4.135457] dwc2 dwc2: ++OTG Interrupt: Debounce Done++
[ 4.135500] console [ttyS0] enabled
[ 4.233802] jz-uart.2: ttyS2 at MMIO 0x10032000 (irq = 57) is a uart2
[ 4.303831] dwc2 dwc2: set feature 4
[ 4.353807] jz-uart.3: ttyS3 at MMIO 0x10033000 (irq = 56) is a uart3
[ 4.453808] jz-uart.4: ttyS4 at MMIO 0x10034000 (irq = 42) is a uart4
[ 4.634073] [drm] Initialized drm 1.1.0 20060810
[ 4.652144] brd: module loaded
[ 4.666261] loop: module loaded
[ 4.677833] pmem_camera: 1 init
[ 4.693833] usb 1-1: new high speed USB device number 4 using dwc2
[ 4.723249] jz-dmmu jz-dmmu.0: page_table_pool_init_capacity=4 table_pool_bitmap=0xf
[ 4.739783] dwc2 dwc2: set feature 4
[ 4.740202] h2clk clk_rate = bebc200
[ 4.752482] max_program_length = 1f
[ 4.764222] use_count = 0
[ 4.774888] is_timer_on = 0
[ 4.785706] gpio_vddq_en_n = 84
[ 4.796872] rd_adj = 8
[ 4.807105] rd_strobe = 7
[ 4.817502] wr_adj = f
[ 4.827559] wr_strobe = 140
[ 4.838032] min_rd_adj = 1
[ 4.848470] min_rd_adj_strobe = 3
[ 4.859577] min_wr_adj = 1
[ 4.869923] min_wr_adj_strobe = 87
[ 4.881000] max_wr_adj_strobe = 217
[ 4.893239] dma dma0chan30: Channel 30 have been requested.(phy id 1,type 0x08)
[ 4.908534] jz4780-nand jz4780-nand.0: enable DMA special channel<0, 1>
[ 4.973477] ONFI param page 0 valid
[ 4.984893] ONFI flash detected
[ 4.995889] NAND device: Manufacturer ID: 0x2c, Chip ID: 0x88 (Micron MT29F64G08CBAAAWP), 8192MiB, page size: 8192, OOB size: 448
[ 5.018509] Bad block table found at page 1048320, version 0x01
[ 5.036321] Bad block table found at page 1048064, version 0x01
[ 5.052543] nand_read_bbt: bad block at 0x00000b400000
[ 5.066222] nand_read_bbt: bad block at 0x00000b600000
[ 5.081309] Creating 2 MTD partitions on "jz4780-nand.0":
[ 5.095085] 0x000000000000-0x000000c00000 : "u-boot"
[ 5.109580] 0x000000c00000-0x000200000000 : "system"
[ 5.124392] jz4780-nand jz4780-nand.0: Successfully registered JZ4780 SoC NAND controller driver.
[ 5.142381] UBI: attaching mtd1 to ubi0
[ 5.154620] UBI: physical eraseblock size: 2097152 bytes (2048 KiB)
[ 5.169683] UBI: logical eraseblock size: 2080768 bytes
[ 5.183755] UBI: smallest flash I/O unit: 8192
[ 5.197056] UBI: VID header offset: 8192 (aligned 8192)
[ 5.211754] UBI: data offset: 16384
[ 5.233891] usb 1-1: New USB device found, idVendor=05ac, idProduct=1006
[ 5.249450] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 5.265488] usb 1-1: Product: Keyboard Hub
[ 5.278323] usb 1-1: Manufacturer: Apple, Inc.
[ 5.291570] usb 1-1: SerialNumber: 000000000000
[ 5.306069] hub 1-1:1.0: USB hub found
[ 5.318953] hub 1-1:1.0: 3 ports detected
[ 5.603984] usb 1-1.2: new low speed USB device number 5 using dwc2
[ 5.619226] dwc2 dwc2: Sorry, SPLIT transfer is not supported!
[ 5.633949] dwc2 dwc2: Sorry, SPLIT transfer is not supported!
[ 5.648572] dwc2 dwc2: Sorry, SPLIT transfer is not supported!
[ 5.753960] usb 1-1.2: device descriptor read/64, error -12
[ 5.863808] dwc2 dwc2: Sorry, SPLIT transfer is not supported!
[ 5.878619] dwc2 dwc2: Sorry, SPLIT transfer is not supported!
[ 5.893319] dwc2 dwc2: Sorry, SPLIT transfer is not supported!
[ 5.983957] usb 1-1.2: device descriptor read/64, error -12
[ 6.183977] usb 1-1.2: new low speed USB device number 6 using dwc2
[ 6.198986] dwc2 dwc2: Sorry, SPLIT transfer is not supported!
[ 6.213499] dwc2 dwc2: Sorry, SPLIT transfer is not supported!
[ 6.227847] dwc2 dwc2: Sorry, SPLIT transfer is not supported!
[ 6.313948] usb 1-1.2: device descriptor read/64, error -12
[ 6.423802] dwc2 dwc2: Sorry, SPLIT transfer is not supported!
[ 6.438264] dwc2 dwc2: Sorry, SPLIT transfer is not supported!
[ 6.452555] dwc2 dwc2: Sorry, SPLIT transfer is not supported!
[ 6.543897] usb 1-1.2: device descriptor read/64, error -12
[ 6.743969] usb 1-1.2: new low speed USB device number 7 using dwc2
[ 6.758812] dwc2 dwc2: Sorry, SPLIT transfer is not supported!
[ 6.963840] dwc2 dwc2: Sorry, SPLIT transfer is not supported!
[ 7.183782] usb 1-1.2: device not accepting address 7, error -12
[ 7.273964] usb 1-1.2: new low speed USB device number 8 using dwc2
[ 7.288757] dwc2 dwc2: Sorry, SPLIT transfer is not supported!
[ 7.503849] dwc2 dwc2: Sorry, SPLIT transfer is not supported!
[ 7.723780] usb 1-1.2: device not accepting address 8, error -12
[ 7.738465] hub 1-1:1.0: unable to enumerate USB device on port 2
[ 10.043837] dwc2 dwc2: Unlink after no-IRQ? Controller is probably using the wrong IRQ.
[ 10.061260] dwc2 dwc2: set feature 2
[ 19.973286] UBI: max. sequence number: 409
[ 20.003749] UBI: attached mtd1 to ubi0
[ 20.016321] UBI: MTD device name: "system"
[ 20.030293] UBI: MTD device size: 8180 MiB
[ 20.044311] UBI: number of good PEBs: 4084
[ 20.057956] UBI: number of bad PEBs: 6
[ 20.071375] UBI: number of corrupted PEBs: 0
[ 20.084787] UBI: max. allowed volumes: 128
[ 20.098284] UBI: wear-leveling threshold: 4096
[ 20.111744] UBI: number of internal volumes: 1
[ 20.124839] UBI: number of user volumes: 2
[ 20.138013] UBI: available PEBs: 0
[ 20.150908] UBI: total number of reserved PEBs: 4084
[ 20.164138] UBI: number of PEBs reserved for bad PEB handling: 40
[ 20.178674] UBI: max/mean erase counter: 7/1
[ 20.191236] UBI: image sequence number: 0
[ 20.203790] UBI: background thread "ubi_bgt0d" started, PID 50
[ 20.203943] dma dma0chan21: Channel 21 have been requested.(phy id 10,type 0x16)
[ 20.203968] dma dma0chan22: Channel 22 have been requested.(phy id 9,type 0x16)
[ 20.250402] JZ47xx SSI Controller for SPI channel 0 driver register
[ 20.265405] dma dma0chan19: Channel 19 have been requested.(phy id 12,type 0x18)
[ 20.281389] dma dma0chan20: Channel 20 have been requested.(phy id 11,type 0x18)
[ 20.297725] JZ47xx SSI Controller for SPI channel 1 driver register
[ 20.313201] PPP generic driver version 2.4.2
[ 20.326183] PPP Deflate Compression module registered
[ 20.339692] PPP BSD Compression module registered
[ 20.354316] PPP MPPE Compression module registered
[ 20.367419] NET: Registered protocol family 24
[ 20.380236] tun: Universal TUN/TAP device driver, 1.6
[ 20.393554] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 20.408463] dm9000 Ethernet Driver, V1.31
[ 20.421087] usbcore: registered new interface driver asix
[ 20.435119] usbcore: registered new interface driver cdc_ether
[ 20.449569] usbcore: registered new interface driver dm9601
[ 20.463619] usbcore: registered new interface driver net1080
[ 20.477668] usbcore: registered new interface driver cdc_subset
[ 20.492008] usbcore: registered new interface driver zaurus
[ 20.505845] cdc_ncm: 04-Aug-2011
[ 20.517313] usbcore: registered new interface driver cdc_ncm
[ 20.531219] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 20.547327] jz-ehci jz-ehci.0: JZ EHCI
[ 20.559553] jz-ehci jz-ehci.0: new USB bus registered, assigned bus number 2
[ 20.575445] jz-ehci jz-ehci.0: irq 28, io mem 0x13490000
[ 20.603767] jz-ehci jz-ehci.0: USB 0.0 started, EHCI 1.00
[ 20.617784] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 20.633315] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 20.649374] usb usb2: Product: JZ EHCI
[ 20.661762] usb usb2: Manufacturer: Linux 3.0.8-00094-gb4f0297c4d84 ehci_hcd
[ 20.677698] usb usb2: SerialNumber: jz
[ 20.690868] hub 2-0:1.0: USB hub found
[ 20.703568] hub 2-0:1.0: 1 port detected
[ 20.716733] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 20.732379] jz-ohci jz-ohci.0: JZ OHCI
[ 20.745094] jz-ohci jz-ohci.0: new USB bus registered, assigned bus number 3
[ 20.761359] jz-ohci jz-ohci.0: irq 13, io mem 0x134a0000
[ 20.837855] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 20.853856] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 20.870227] usb usb3: Product: JZ OHCI
[ 20.883158] usb usb3: Manufacturer: Linux 3.0.8-00094-gb4f0297c4d84 ohci_hcd
[ 20.899557] usb usb3: SerialNumber: jz
[ 20.913018] hub 3-0:1.0: USB hub found
[ 20.925790] hub 3-0:1.0: 1 port detected
[ 20.939076] usbcore: registered new interface driver uas
[ 20.953396] Initializing USB Mass Storage driver...
[ 20.967469] usbcore: registered new interface driver usb-storage
[ 20.982669] USB Mass Storage support registered.
[ 20.996620] usbcore: registered new interface driver usbserial
[ 21.011735] usbserial: USB Serial Driver core
[ 21.025438] USB Serial support registered for GSM modem (1-port)
[ 21.041299] usbcore: registered new interface driver option
[ 21.056400] option: v0.7.2:USB Driver for GSM modems
[ 21.070847] dwc2 dwc2: registering gadget driver 'g_cdc'
[ 21.085753] dwc2 dwc2: bind to driver g_cdc
[ 21.099540] g_cdc gadget: using random self ethernet address
[ 21.114845] g_cdc gadget: using random host ethernet address
[ 21.130434] usb0: MAC 1e:fb:d8:11:91:33
[ 21.143755] usb0: HOST MAC 9e:85:c7:6f:29:61
[ 21.157830] g_cdc gadget: CDC Composite Gadget, version: King Kamehameha Day 2008
[ 21.175038] g_cdc gadget: g_cdc ready
[ 21.188175] dwc2 dwc2: registered gadget driver 'g_cdc'
[ 21.203472] mousedev: PS/2 mouse device common for all mice
[ 21.219097] input: jz-remote as /devices/platform/jz-remote/input/input0
[ 21.235750] The remote driver registe success
[ 21.250554] using rtc device, jz-rtc, for alarms
[ 21.255391] jz-rtc jz-rtc.0: rtc core: registered jz-rtc as rtc0
[ 21.280420] jz4780-rtc: rtc status reset by power-on
[ 21.296772] lirc_dev: IR Remote Control driver registered, major 251
[ 21.312972] IR NEC protocol handler initialized
[ 21.327154] IR RC5(x) protocol handler initialized
[ 21.341594] IR RC6 protocol handler initialized
[ 21.355833] IR JVC protocol handler initialized
[ 21.369867] IR Sony protocol handler initialized
[ 21.383937] IR RC5 (streamzap) protocol handler initialized
[ 21.399010] IR LIRC bridge handler initialized
[ 21.412977] Linux video capture interface: v2.00
[ 21.427519] soc-camera-pdrv soc-camera-pdrv: register ok!
[ 21.443414] device-mapper: uevent: version 1.0.3
[ 21.458482] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@redhat.com
[ 21.477275] Bluetooth: HCI UART driver ver 2.2
[ 21.491755] Bluetooth: HCI H4 protocol initialized
[ 21.506623] Bluetooth: HCILL protocol initialized
[ 21.521295] Bluetooth: Generic Bluetooth USB driver ver 0.6
[ 21.536914] usbcore: registered new interface driver btusb
[ 21.552855] jzmmc jzmmc.0: vmmc.0 regulator miss
[ 21.568776] jzmmc jzmmc.1: vmmc.1 regulator miss
[ 21.584853] usbcore: registered new interface driver usbhid
[ 21.600240] usbhid: USB HID core driver
[ 21.614956] jzmmc jzmmc.0: err1 cmd52 iflg00002204 status1F000942
[ 21.631957] jzmmc jzmmc.0: err1 cmd52 iflg00002204 status1F000842
[ 21.652369] jzmmc jzmmc.0: err1 cmd8 iflg00002204 status1F000942
[ 21.668941] jzmmc jzmmc.0: err1 cmd5 iflg00002204 status1F000942
[ 21.685460] jzmmc jzmmc.0: err1 cmd5 iflg00002204 status1F000942
[ 21.701952] jzmmc jzmmc.0: err1 cmd5 iflg00002204 status1F000942
[ 21.718344] jzmmc jzmmc.0: err1 cmd5 iflg00002204 status1F000942
[ 21.734485] jzmmc jzmmc.0: err1 cmd55 iflg00002204 status1F000942
[ 21.750742] jzmmc jzmmc.0: err1 cmd55 iflg00002204 status1F000942
[ 21.766863] jzmmc jzmmc.0: err1 cmd55 iflg00002204 status1F000942
[ 21.782765] jzmmc jzmmc.0: err1 cmd55 iflg00002204 status1F000942
[ 21.798925] jzmmc jzmmc.0: err1 cmd1 iflg00002204 status1F000942
[ 21.855834] jzmmc jzmmc.0: err1 cmd52 iflg00002204 status1F000942
[ 21.872368] jzmmc jzmmc.0: err1 cmd52 iflg00002204 status1F000942
[ 21.893044] jzmmc jzmmc.0: err1 cmd8 iflg00002204 status1F000942
[ 21.909288] jzmmc jzmmc.0: err1 cmd5 iflg00002204 status1F000942
[ 21.925530] jzmmc jzmmc.0: err1 cmd5 iflg00002204 status1F000942
[ 21.941675] jzmmc jzmmc.0: err1 cmd5 iflg00002204 status1F000942
[ 21.957732] jzmmc jzmmc.0: err1 cmd5 iflg00002204 status1F000942
[ 21.973604] jzmmc jzmmc.0: err1 cmd55 iflg00002204 status1F000942
[ 21.989474] jzmmc jzmmc.0: err1 cmd55 iflg00002204 status1F000942
[ 22.005292] jzmmc jzmmc.0: err1 cmd55 iflg00002204 status1F000942
[ 22.020883] jzmmc jzmmc.0: err1 cmd55 iflg00002204 status1F000942
[ 22.036793] jzmmc jzmmc.0: err1 cmd1 iflg00002204 status1F000942
[ 22.085833] jzmmc jzmmc.0: err1 cmd52 iflg00002204 status1F000942
[ 22.101204] jzmmc jzmmc.0: err1 cmd52 iflg00002204 status1F000942
[ 22.120746] jzmmc jzmmc.0: err1 cmd8 iflg00002204 status1F000942
[ 22.135883] jzmmc jzmmc.0: err1 cmd5 iflg00002204 status1F000942
[ 22.150871] jzmmc jzmmc.0: err1 cmd5 iflg00002204 status1F000942
[ 22.165935] jzmmc jzmmc.0: err1 cmd5 iflg00002204 status1F000942
[ 22.180735] jzmmc jzmmc.0: err1 cmd5 iflg00002204 status1F000942
[ 22.195542] jzmmc jzmmc.0: err1 cmd55 iflg00002204 status1F000942
[ 22.210257] jzmmc jzmmc.0: err1 cmd55 iflg00002204 status1F000942
[ 22.224883] jzmmc jzmmc.0: err1 cmd55 iflg00002204 status1F000942
[ 22.239345] jzmmc jzmmc.0: err1 cmd55 iflg00002204 status1F000942
[ 22.254108] jzmmc jzmmc.0: err1 cmd1 iflg00002204 status1F000942
[ 22.546346] asoc: jz4780-hifi <-> jz4780-i2s mapping ok
[ 22.558575] input: ci20 Headphone Jack as /devices/platform/soc-audio/sound/card0/input1
[ 22.573927] ALSA device list:
[ 22.583179] #0: ci20
[ 22.591928] Netfilter messages via NETLINK v0.30.
[ 22.603081] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 22.616507] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 22.629263] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 22.641288] TCP cubic registered
[ 22.651836] NET: Registered protocol family 10
[ 22.663750] Mobile IPv6
[ 22.672588] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 22.684765] IPv6 over IPv4 tunneling driver
[ 22.696006] NET: Registered protocol family 17
[ 22.707226] Bridge firewalling registered
[ 22.718019] Bluetooth: RFCOMM TTY layer initialized
[ 22.729463] Bluetooth: RFCOMM socket layer initialized
[ 22.740961] Bluetooth: RFCOMM ver 1.11
[ 22.750907] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 22.762539] Bluetooth: BNEP filters: protocol multicast
[ 22.774147] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 22.774312] lib80211: common routines for IEEE802.11 drivers
[ 22.774322] lib80211_crypt: registered algorithm 'NULL'
[ 22.774331] Registering the dns_resolver key type
[ 22.774682] dm9000 power on
[ 22.834767] eth0: dm9000b at b6000000,b6000002 IRQ 220 MAC: d0:31:10:ff:7d:02 (platform data)
[ 22.851618] x2d x2d: Virtual Driver of JZ X2D registered
[ 22.863484] Virtual Driver of JZ X2D registered
[ 23.504143]
[ 23.504149] Dongle Host Driver, version 5.90.195.89
[ 23.504154] Compiled in drivers/net/wireless/bcmdhd on Jun 25 2014 at 12:22:45
[ 23.554806] jzmmc jzmmc.1: err1 cmd52 iflg00002200 status1F000142
[ 23.568979] jzmmc jzmmc.1: err1 cmd52 iflg00002204 status1F000942
[ 23.586845] jzmmc jzmmc.1: err1 cmd8 iflg00002204 status1F000942
[ 23.611158] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[ 23.625724] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 23.640341] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 23.656326] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[ 23.717091] jzmmc jzmmc.1: clk_want: 24000000, clk_set: 24000000Hz
[ 23.730856] jzmmc jzmmc.1: clk_want: 24000000, clk_set: 24000000Hz
[ 23.751566] mmc1: new SDIO card at address 0001
[ 23.765600] F1 signature read @0x18000000=0x16044330
[ 23.780868] DHD: dongle ram size is set to 294912(orig 294912)
[ 23.795277] wl_create_event_handler thr:3f started
[ 23.808238] dhd_attach thr:40 started
[ 23.819880] dhd_attach thr:41 started
[ 23.831494] dhd_attach thr:42 started
[ 23.844365] Broadcom Dongle Host Driver: register interface [wlan0] MAC: 00:90:4c:11:22:33
[ 23.861255] =========== WLAN placed in RESET ========
[ 23.875894] jz-rtc jz-rtc.0: setting system clock to 2012-06-01 12:00:02 UTC (1338552002)
[ 24.385081] RET<0
[ 24.395338] ov5640 2-003c: i2c write failed!
[ 24.408111] ov5640: probe of 2-003c failed with error -1
[ 25.462543] UBIFS: recovery needed
[ 27.229910] UBIFS: recovery completed
[ 27.242683] UBIFS: mounted UBI device 0, volume 1, name "root"
[ 27.257387] UBIFS: file system size: 8316829696 bytes (8121904 KiB, 7931 MiB, 3997 LEBs)
[ 27.274854] UBIFS: journal size: 18726913 bytes (18288 KiB, 17 MiB, 9 LEBs)
[ 27.291588] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 27.306705] UBIFS: default compressor: lzo
[ 27.320092] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 27.344887] VFS: Mounted root (ubifs filesystem) on device 0:11.
[ 27.361158] Freeing unused kernel memory: 232k freed
[ 37.410320] graphics fb0: open count : 2
[ 37.423649] [drm] Initialized jz4780-sgx 1.11.2580795 20110701 on minor 0
[ 41.407854] UBIFS: recovery needed
[ 41.915650] UBIFS: recovery completed
[ 41.929419] UBIFS: mounted UBI device 0, volume 0, name "boot"
[ 41.945059] UBIFS: file system size: 47857664 bytes (46736 KiB, 45 MiB, 23 LEBs)
[ 41.962627] UBIFS: journal size: 18726913 bytes (18288 KiB, 17 MiB, 9 LEBs)
[ 41.980097] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 41.995821] UBIFS: default compressor: lzo
[ 42.009733] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 46.653918] cljiang------bt_power_control,enable = 1
[ 55.023960] dm9000 dm9000.0: eth0: link down
[ 55.029000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 55.293650] ADDRCONF(NETDEV_UP): usb0: link is not ready
[ 55.348229]
[ 55.348242] Dongle Host Driver, version 5.90.195.89
[ 55.348247] Compiled in drivers/net/wireless/bcmdhd on Jun 25 2014 at 12:22:45
[ 55.362789] wl_android_wifi_on in
[ 55.366386] =========== WLAN going back to live ========
[ 55.993943] sdio_reset_comm():
[ 55.997117] jzmmc jzmmc.1: clk_want: 24000000, clk_set: 24000000Hz
[ 56.010291] jzmmc jzmmc.1: clk_want: 24000000, clk_set: 24000000Hz
[ 56.024011] jzmmc jzmmc.1: clk_want: 24000000, clk_set: 24000000Hz
[ 56.030544] jzmmc jzmmc.1: clk_want: 24000000, clk_set: 24000000Hz
[ 56.525921] dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded.
[ 56.684653] Firmware up: op_mode=1, Broadcom Dongle Host Driver mac=98:3b:16:be:41:ee
[ 56.814698] Firmware version = wl0: May 9 2012 23:14:16 version 5.90.195.26.2 FWID 01-1229e594
[ 56.934456] dhd_rx_frame: net device is NOT registered yet. drop packet
[ 56.941354] dhd_rx_frame: net device is NOT registered yet. drop packet
[ 57.224402] wl_android_wifi_off in
[ 57.229159] =========== WLAN placed in RESET ========
[ 57.747420] dhd_prot_ioctl : bus is down. we have nothing to do
[ 57.753580] wlan0: set cur_etheraddr failed
[ 57.760203]
[ 57.760217] Dongle Host Driver, version 5.90.195.89
[ 57.760222] Compiled in drivers/net/wireless/bcmdhd on Jun 25 2014 at 12:22:45
[ 57.774247] wl_android_wifi_on in
[ 57.777680] =========== WLAN going back to live ========
[ 58.384023] sdio_reset_comm():
[ 58.387248] jzmmc jzmmc.1: clk_want: 24000000, clk_set: 24000000Hz
[ 58.396103] jzmmc jzmmc.1: clk_want: 24000000, clk_set: 24000000Hz
[ 58.407694] jzmmc jzmmc.1: clk_want: 24000000, clk_set: 24000000Hz
[ 58.415336] jzmmc jzmmc.1: clk_want: 24000000, clk_set: 24000000Hz
[ 58.424657] F1 signature read @0x18000000=0x16044330
[ 69.474248] wlan0: no IPv6 routers present
[ 300.649664] JZ4780-EFUSE: vddq_set 0
[ 379.421603] usb 1-1: USB disconnect, device number 4
[ 380.273070] dwc2 dwc2: ++OTG Interrupt: A-Device Timeout Change++
[ 382.541660] usb 2-1: new high speed USB device number 2 using jz-ehci
[ 382.700935] usb 2-1: New USB device found, idVendor=05ac, idProduct=1006
[ 382.708129] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 382.715810] usb 2-1: Product: Keyboard Hub
[ 382.720065] usb 2-1: Manufacturer: Apple, Inc.
[ 382.724928] usb 2-1: SerialNumber: 000000000000
[ 382.732755] hub 2-1:1.0: USB hub found
[ 382.737018] hub 2-1:1.0: 3 ports detected
[ 383.021878] usb 2-1.2: new low speed USB device number 3 using jz-ehci
[ 383.138815] usb 2-1.2: New USB device found, idVendor=05ac, idProduct=024f
[ 383.146199] usb 2-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 383.153958] usb 2-1.2: Product: Apple Keyboard
[ 383.158610] usb 2-1.2: Manufacturer: Apple Inc.
[ 383.172441] input: Apple Inc. Apple Keyboard as /devices/platform/jz-ehci.0/usb2/2-1/2-1.2/2-1.2:1.0/input/input2
[ 383.184220] generic-usb 0003:05AC:024F.0001: input: USB HID v1.11 Keyboard [Apple Inc. Apple Keyboard] on usb-jz-1.2/input0
[ 383.202155] input: Apple Inc. Apple Keyboard as /devices/platform/jz-ehci.0/usb2/2-1/2-1.2/2-1.2:1.1/input/input3
[ 383.213628] generic-usb 0003:05AC:024F.0002: input: USB HID v1.11 Device [Apple Inc. Apple Keyboard] on usb-jz-1.2/input1
[ 432.390663] dwc2 dwc2: ++OTG Interrupt: Debounce Done++
[ 432.412901] dwc2 dwc2: set feature 4
[ 432.802824] usb 1-1: new low speed USB device number 9 using dwc2
[ 432.809981] dwc2 dwc2: set feature 4
[ 433.218970] usb 1-1: New USB device found, idVendor=045e, idProduct=007d
[ 433.225943] usb 1-1: New USB device strings: Mfr=1, Product=3, SerialNumber=0
[ 433.233810] usb 1-1: Product: Microsoft 3-Button Mouse with IntelliEye\xffffffe2\xffffff84\xffffffa2\xffffff84\xffffffa2
[ 433.240813] usb 1-1: Manufacturer: Microsoft
[ 433.264362] input: Microsoft Microsoft 3-Button Mouse with IntelliEye\xffffffe2\xffffff84\xffffffa2\xffffff84\xffffffa2 as /devices/platform/jz4780-dwc2/dwc2/usb1/1-1/1-1:1.0/input/input4
[ 433.278841] generic-usb 0003:045E:007D.0003: input: USB HID v1.00 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye\xffffffe2\xffffff84\xffffffa2\xffffff84\xffffffa2] on usb-dwc2-1/input0
[ 689.783040] dma dma0chan23: Channel 23 have been requested.(phy id 8,type 0x06)
[ 690.029388] dma dma0chan24: Channel 24 have been requested.(phy id 7,type 0x06)
[ 690.129322] dma dma0chan23: Channel 23 have been requested.(phy id 8,type 0x06)
[ 690.145946] dma dma0chan24: Channel 24 have been requested.(phy id 7,type 0x06)
[ 690.174372] dma dma0chan23: Channel 23 have been requested.(phy id 8,type 0x06)
[ 690.446385] dma dma0chan23: Channel 23 have been requested.(phy id 8,type 0x06)
[ 690.879731] dma dma0chan24: Channel 24 have been requested.(phy id 7,type 0x06)
[ 1286.973239] wl_android_wifi_off in
[ 1286.977625] =========== WLAN placed in RESET ========
[ 1287.494855] net_ratelimit: 5 callbacks suppressed
[ 1287.496326] wl_android_wifi_on in
[ 1287.503792] dhd_prot_ioctl : bus is down. we have nothing to do
[ 1287.509908] wlan0: set cur_etheraddr failed
[ 1287.514603] =========== WLAN going back to live ========
[ 1288.142842] sdio_reset_comm():
[ 1288.146018] jzmmc jzmmc.1: clk_want: 24000000, clk_set: 24000000Hz
[ 1288.154901] jzmmc jzmmc.1: clk_want: 24000000, clk_set: 24000000Hz
[ 1288.166267] jzmmc jzmmc.1: clk_want: 24000000, clk_set: 24000000Hz
[ 1288.173209] jzmmc jzmmc.1: clk_want: 24000000, clk_set: 24000000Hz
[ 1288.180834] F1 signature read @0x18000000=0x16044330
[ 1288.189239] DHD: dongle ram size is set to 294912(orig 294912)
[ 1288.283150] dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded.
[ 1288.423149] Firmware up: op_mode=1, Broadcom Dongle Host Driver mac=98:3b:16:be:41:ee
[ 1288.553789] Firmware version = wl0: May 9 2012 23:14:16 version 5.90.195.26.2 FWID 01-1229e594
[ 1288.673388] wl_host_event: Invalid ifidx 0 for wl0
[ 1298.933063] wlan0: no IPv6 routers present
[ 1588.470450] connect failed event=0 e->status 0x1
[ 1588.475228] CFG80211-ERROR) wl_bss_connect_done : Report connect result - connection failed
[ 1600.340851] connect failed event=0 e->status 0x1
[ 1600.345638] CFG80211-ERROR) wl_bss_connect_done : Report connect result - connection failed
[ 1612.220882] connect failed event=0 e->status 0x1
[ 1612.225722] CFG80211-ERROR) wl_bss_connect_done : Report connect result - connection failed
[ 1627.601455] connect failed event=0 e->status 0x1
[ 1627.606234] CFG80211-ERROR) wl_bss_connect_done : Report connect result - connection failed
[ 1639.161680] connect failed event=0 e->status 0x1
[ 1639.166935] CFG80211-ERROR) wl_bss_connect_done : Report connect result - connection failed
[ 1651.051852] connect failed event=0 e->status 0x1
[ 1651.056693] CFG80211-ERROR) wl_bss_connect_done : Report connect result - connection failed
[ 1745.004525] wl_bss_connect_done succeeded
[ 1745.044377] wl_bss_connect_done succeeded
[ 1755.593805] wlan0: no IPv6 routers present
[ 1920.016899] CFG80211-ERROR) wl_cfg80211_disconnect : Reason 3
[ 1920.129054] cfg80211: Calling CRDA for country: US
[ 1920.168265] wl_android_wifi_off in
[ 1920.172681] =========== WLAN placed in RESET ========
[ 1920.260772] cfg80211: Regulatory domain changed to country: US
[ 1920.266795] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 1920.275454] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 1920.283643] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[ 1920.291828] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 1920.300012] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 1920.308191] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 1920.316355] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[ 1920.324587] cfg80211: Calling CRDA to update world regulatory domain
[ 1920.370548] cfg80211: World regulatory domain updated:
[ 1920.375857] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 1920.384558] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 1920.392774] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 1920.400949] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 1920.409138] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 1920.417298] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 1920.696251] dhd_prot_ioctl : bus is down. we have nothing to do
[ 1920.703671] wlan0: set cur_etheraddr failed
[ 1920.708897]
[ 1920.708908] Dongle Host Driver, version 5.90.195.89
[ 1920.708913] Compiled in drivers/net/wireless/bcmdhd on Jun 25 2014 at 12:22:45
[ 1920.722984] wl_android_wifi_on in
[ 1920.726403] =========== WLAN going back to live ========
[ 1921.357770] sdio_reset_comm():
[ 1921.360963] jzmmc jzmmc.1: clk_want: 24000000, clk_set: 24000000Hz
[ 1921.369508] jzmmc jzmmc.1: clk_want: 24000000, clk_set: 24000000Hz
[ 1921.380897] jzmmc jzmmc.1: clk_want: 24000000, clk_set: 24000000Hz
[ 1921.387478] jzmmc jzmmc.1: clk_want: 24000000, clk_set: 24000000Hz
[ 1921.395469] F1 signature read @0x18000000=0x16044330
[ 1921.404049] DHD: dongle ram size is set to 294912(orig 294912)
[ 1921.503141] dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded.
[ 1921.640396] Firmware up: op_mode=1, Broadcom Dongle Host Driver mac=98:3b:16:be:41:ee
[ 1921.798411] Firmware version = wl0: May 9 2012 23:14:16 version 5.90.195.26.2 FWID 01-1229e594
[ 1921.908394] wl_host_event: Invalid ifidx 0 for wl0
[ 1932.757953] wlan0: no IPv6 routers present
[ 2284.326076] dma dma0chan23: Channel 23 have been requested.(phy id 8,type 0x06)
[ 2284.360237] dma dma0chan24: Channel 24 have been requested.(phy id 7,type 0x06)
[ 2284.415100] dma dma0chan23: Channel 23 have been requested.(phy id 8,type 0x06)
[ 2284.434057] dma dma0chan24: Channel 24 have been requested.(phy id 7,type 0x06)
[ 2284.467530] dma dma0chan23: Channel 23 have been requested.(phy id 8,type 0x06)
[ 2284.492991] dma dma0chan23: Channel 23 have been requested.(phy id 8,type 0x06)
[ 2284.570718] dma dma0chan24: Channel 24 have been requested.(phy id 7,type 0x06)
[ 2320.677814] wl_bss_connect_done succeeded
[ 2320.738085] cfg80211: Calling CRDA for country: US
[ 2320.743158] wl_bss_connect_done succeeded
[ 2320.868498] cfg80211: Regulatory domain changed to country: US
[ 2320.874706] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 2320.883475] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 2320.891703] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[ 2320.899911] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 2320.908152] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 2320.916322] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 2320.924606] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[ 2331.857341] wlan0: no IPv6 routers present
[ 5582.557600] dma dma0chan23: Channel 23 have been requested.(phy id 8,type 0x06)